more careful

Author: CamDavidsonPilon

user-guide/01-getting-started/01-assembly_guides/00-kit-assembly/00_pioreactor_40ml_v1.5/05-40ml-v15-optics-assembly.md

@@ -57,11 +57,11 @@ The measuring eye-spy can be placed in either the 90 or 135 degree pocket. For m
 <AssemblyInstructionBlock title="Step 3: Connect eye-spys to HAT" images={["user-guide/hardware-assembly/40ml-v15/connect-stemma-to-hat.jpg", "user-guide/hardware-assembly/40ml-v15/connect-stemma-on-eye-spy.jpg"]}>
 
 1. Locate the <Highlight color={colors.teal}>STEMMA-QT connector</Highlight> on the HAT and connect the 100mm STEMMA-QT wire, with the yellow wire furthest from the heater flat flex cable. 
-2. Connect the other end to the leftmost eye-spy. Use the colors of the wire to orient the connector correctly. 
+2. Carefully connect the other end to the leftmost eye-spy. Use the colors of the wire to orient the connector correctly. 
 3. Use the <Highlight color={colors.magenta}>50mm STEMMA-QT wire</Highlight> to connect each eye-spy. 
 
 :::tip
-It does not matter which wires are connected to either eye-spy sockets. However, organize the wires neatly and avoid crossing over when possible.
+It does not matter which wires are connected to either eye-spy sockets. However, organize the wires neatly and avoid crossing over when possible. Insert each connector carefully and straight; pushing too hard can damage an internal pin.
 :::
 
 
@@ -94,4 +94,4 @@ Your new 40ml Pioreactor v1.5 is now assembled! 🚀
 Next: begin installing the [software](/user-guide/software-set-up).
 
 
-</AssemblyInstructionBlock>
+</AssemblyInstructionBlock>

user-guide/01-getting-started/01-assembly_guides/00-kit-assembly/01_pioreactor_20ml_v1.5/05-20ml-v15-optics-assembly.md

@@ -56,12 +56,12 @@ The measuring eye-spy can be placed in either the 90 or 135 degree pocket. For m
 <AssemblyInstructionBlock title="Step 3: Connect eye-spys to HAT" images={["user-guide/hardware-assembly/40ml-v15/connect-stemma-to-hat.jpg", "user-guide/hardware-assembly/20ml-v15/connect-stemma-on-eye-spy.jpg"]}>
 
 1. Locate the <Highlight color={colors.teal}>Stemma-QT connector</Highlight> on the HAT and connect the 100mm Stemma-QT wire, with the yellow wire furthest from the heater flat flex cable. 
-2. Connect the other end to the leftmost eye-spy. Use the colors of the wire to orient the connector correctly. 
+2. Carefully connect the other end to the leftmost eye-spy. Use the colors of the wire to orient the connector correctly. 
 3. Use the <Highlight color={colors.magenta}>50mm Stemma-QT wire</Highlight> to connect each eye-spy. 
 
 
 :::tip
-It does not matter which wires are connected to either eye-spy sockets. However, organize the wires neatly and avoid crossing over when possible.
+It does not matter which wires are connected to either eye-spy sockets. However, organize the wires neatly and avoid crossing over when possible. Insert each connector carefully and straight; pushing too hard can damage an internal pin.
 :::
 
 
@@ -94,4 +94,4 @@ Your new 20ml Pioreactor v1.5 is now assembled! 🚀
 Next: begin installing the [software](/user-guide/software-set-up).
 
 
-</AssemblyInstructionBlock>
+</AssemblyInstructionBlock>

user-guide/01-getting-started/01-assembly_guides/01-upgrade-assembly/03_pioreactor_40ml_v1.5_to_XR/02-40ml-XR-assembly.md

@@ -57,17 +57,17 @@ import TabItem from '@theme/TabItem';
 
 <AssemblyInstructionBlock title="Step 5: Connect the eye-spys" images={["user-guide/hardware-assembly/upgrade_XR/connect-100mm-to-45.jpg", "user-guide/hardware-assembly/upgrade_XR/connect-100mm-45-to-ref.jpg", "user-guide/hardware-assembly/upgrade_XR/connect-50mm-ref-to-90.jpg", "user-guide/hardware-assembly/upgrade_XR/connect-50mm-90-to-135.jpg"]}>
 
-1. A 100mm STEMMA-QT wire should be still connected to the HAT. <Highlight color={colors.magenta}>Connect the other end to the leftmost, 45 degree eye-spy</Highlight>. Pay attention to the wire orientation: the yellow wire should be at the bottom.
+1. A 100mm STEMMA-QT wire should be still connected to the HAT. <Highlight color={colors.magenta}>Carefully connect the other end to the leftmost, 45 degree eye-spy</Highlight>. Pay attention to the wire orientation: the yellow wire should be at the bottom.
 
 :::caution
 Do not push the wire connector in at an angle, as it can bend the metal leads in the eye-spy connector. 
 :::
 
-2. Using the other 100mm STEMMA-QT wire, <Highlight color={colors.blue}>connect the 45 degree eye-spy to REF</Highlight>. Note the wire orientation. 
+2. Using the other 100mm STEMMA-QT wire, <Highlight color={colors.blue}>carefully connect the 45 degree eye-spy to REF</Highlight>. Note the wire orientation. 
 
-3. Use a 50mm STEMMA-QT wire to connect the <Highlight color={colors.red}>REF eye-spy to the 90 degree eye-spy</Highlight>.
+3. Use a 50mm STEMMA-QT wire to carefully connect the <Highlight color={colors.red}>REF eye-spy to the 90 degree eye-spy</Highlight>.
 
-3. Finally, use the last 50mm STEMMA-QT to connect the <Highlight color={colors.green}>90 degree eye-spy to the 135 degree eye-spy</Highlight>. All eye-spys should now be daisy chained to each other. 
+3. Finally, use the last 50mm STEMMA-QT to carefully connect the <Highlight color={colors.green}>90 degree eye-spy to the 135 degree eye-spy</Highlight>. All eye-spys should now be daisy chained to each other. 
 
 </AssemblyInstructionBlock>
 
@@ -99,4 +99,3 @@ Your new 40ml Pioreactor XR is now assembled!
 
 
 </AssemblyInstructionBlock>
-

user-guide/01-getting-started/01-assembly_guides/01-upgrade-assembly/04_pioreactor_20ml_v1.5_to_XR/02-20ml-XR-assembly.md

@@ -57,17 +57,17 @@ import TabItem from '@theme/TabItem';
 
 <AssemblyInstructionBlock title="Step 5: Connect the eye-spys" images={["user-guide/hardware-assembly/upgrade_XR/connect-100mm-to-45.jpg", "user-guide/hardware-assembly/upgrade_XR/20-connect-100mm-45-to-ref.jpg", "user-guide/hardware-assembly/upgrade_XR/20-connect-50mm-ref-to-90.jpg", "user-guide/hardware-assembly/upgrade_XR/20-connect-50mm-90-to-135.jpg"]}>
 
-1. A 100mm STEMMA-QT wire should be still connected to the HAT. <Highlight color={colors.magenta}>Connect the other end to the leftmost, 45 degree eye-spy</Highlight>. Pay attention to the wire orientation: the yellow wire should be at the bottom.
+1. A 100mm STEMMA-QT wire should be still connected to the HAT. <Highlight color={colors.magenta}>Carefully connect the other end to the leftmost, 45 degree eye-spy</Highlight>. Pay attention to the wire orientation: the yellow wire should be at the bottom.
 
 :::caution
 Do not push the wire connector in at an angle, as it can bend the metal leads in the eye-spy connector. 
 :::
 
-2. Using the other 100mm STEMMA-QT wire, <Highlight color={colors.blue}>connect the 45 degree eye-spy to REF</Highlight>. Note the wire orientation. 
+2. Using the other 100mm STEMMA-QT wire, <Highlight color={colors.blue}>carefully connect the 45 degree eye-spy to REF</Highlight>. Note the wire orientation. 
 
-3. Use a 50mm STEMMA-QT wire to connect the <Highlight color={colors.red}>REF eye-spy to the 90 degree eye-spy</Highlight>.
+3. Use a 50mm STEMMA-QT wire to carefully connect the <Highlight color={colors.red}>REF eye-spy to the 90 degree eye-spy</Highlight>.
 
-3. Finally, use the last 50mm STEMMA-QT to connect the <Highlight color={colors.green}>90 degree eye-spy to the 135 degree eye-spy</Highlight>. All eye-spys should now be daisy chained to each other. 
+3. Finally, use the last 50mm STEMMA-QT to carefully connect the <Highlight color={colors.green}>90 degree eye-spy to the 135 degree eye-spy</Highlight>. All eye-spys should now be daisy chained to each other. 
 
 </AssemblyInstructionBlock>
 
@@ -101,4 +101,3 @@ Your new 20ml Pioreactor XR is now assembled!
 
 </AssemblyInstructionBlock>
 
-

user-guide/01-getting-started/01-assembly_guides/01-upgrade-assembly/06_pioreactor_20ml_v1.1_to_v1.5/05-20ml-v15-optics-assembly.md

@@ -55,12 +55,12 @@ The measuring eye-spy can be placed in either the 90 or 135 degree pocket. For m
 <AssemblyInstructionBlock title="Step 3: Connect eye-spys to HAT" images={["user-guide/hardware-assembly/40ml-v15/connect-stemma-to-hat.jpg", "user-guide/hardware-assembly/20ml-v15/connect-stemma-on-eye-spy.jpg"]}>
 
 1. Locate the <Highlight color={colors.teal}>STEMMA-QT connector</Highlight> on the HAT and connect the 100mm STEMMA-QT wire, with the yellow wire furthest from the heater flat flex cable.
-2. Connect the other end to the leftmost eye-spy. Use the colors of the wire to orient the connector correctly. 
+2. Carefully connect the other end to the leftmost eye-spy. Use the colors of the wire to orient the connector correctly. 
 3. Use the <Highlight color={colors.magenta}>50mm STEMMA-QT wire</Highlight> to connect each eye-spy.
 
 
 :::tip
-It does not matter which wires are connected to either eye-spy sockets. However, organize the wires neatly and avoid crossing over when possible.
+It does not matter which wires are connected to either eye-spy sockets. However, organize the wires neatly and avoid crossing over when possible. Insert each connector carefully and straight; pushing too hard can damage an internal pin.
 :::
 
 

user-guide/01-getting-started/01-assembly_guides/01-upgrade-assembly/07_pioreactor_40ml_v1.0_to_v1.5/05-40ml-v15-optics-assembly.md

@@ -56,11 +56,11 @@ The measuring eye-spy can be placed in either the 90 or 135 degree pocket. For m
 <AssemblyInstructionBlock title="Step 3: Connect eye-spys to HAT" images={["user-guide/hardware-assembly/40ml-v15/connect-stemma-to-hat.jpg", "user-guide/hardware-assembly/40ml-v15/connect-stemma-on-eye-spy.jpg"]}>
 
 1. Locate the <Highlight color={colors.teal}>STEMMA-QT connector</Highlight> on the HAT and connect the 100mm STEMMA-QT wire, with the yellow wire furthest from the heater flat flex cable. 
-2. Connect the other end to the leftmost eye-spy. Use the colors of the wire to orient the connector correctly. 
+2. Carefully connect the other end to the leftmost eye-spy. Use the colors of the wire to orient the connector correctly. 
 3. Use the <Highlight color={colors.magenta}>50mm STEMMA-QT wire</Highlight> to connect each eye-spy. 
 
 :::tip
-It does not matter which wires are connected to either eye-spy sockets. However, organize the wires neatly and avoid crossing over when possible.
+It does not matter which wires are connected to either eye-spy sockets. However, organize the wires neatly and avoid crossing over when possible. Insert each connector carefully and straight; pushing too hard can damage an internal pin.
 :::