Cannot get two controllers (intelligent and motion) to communicate with each other

[console-beaver]

We are trying to use your code (thanks alot for publishing it), but cannot get both controllers to negotiate. So intelligent controller keep sending CAN Bus packets to motion controller and motion controller's light stays red and never turned to blue.

Can you explain which CAN interface need to be connected to each controller? I.e. is it can1 connected to intelligent controller and can2 - to motion controller? Is it opposite? Thanks!

[console-beaver]

Tried to switch can buses around, i.e. can 1 goes to motion controller and can2 - to intelligent controller, but no worky.

Curious if anyone else besides the author got it working using this code?

[console-beaver]

Which S1 firmware you did test this code against?
Apparently, it doesn't work on our S1 which is running very old (original) firmware release...

[JohnieBraaf]

Yes, I can confirm it is working. I suspect that you're can bus timing is off. Make sure you clock it at 1Mbit.

[console-beaver]

Oh sorry, that was the very old question. I got it working too awhile ago.

[krvcz]

Oh sorry, that was the very old question. I got it working too awhile ago.

Hi, how exactly did you solve the problem? Where should I set Can to 1 Mbit?

[console-beaver]

@krvcz my issue was related to CAN bus physical connection and not the baud rate, and could be different from your issue. Basically, I was trying to connect it to both intelligent controller and motion controller at the same time with both CAN1 and CAN2 interfaces. Now with the new code, the intelligent controller was eliminated completely, and you have to use CAN1 interface only (by default, unless you change the code to use CAN2 instead).

[krvcz]

@krvcz my issue was related to CAN bus physical connection and not the baud rate, and could be different from your issue. Basically, I was trying to connect it to both intelligent controller and motion controller at the same time with both CAN1 and CAN2 interfaces. Now with the new code, the intelligent controller was eliminated completely, and you have to use CAN1 interface only (by default, unless you change the code to use CAN2 instead).

Thank you for reply. We stack with this project, so do you have any photos with connectivity ? Can we chat somewhere , for example gmail or Facebook etc.

Now i can’t download project, with error „no such or directory in lwip/otp.h „

[JohnieBraaf]

You only need 1 CAN bus is the latest version of the software. Still had it laying around so see pic.
In his previous version he indeed programmed it as a passthrough device. Not anymore.
It has been couple of month ago and I have not checked after that.

I also wrote a micropython version but it's not yet finished, it spins the wheels though. Let me know if interested.

[JohnieBraaf]

For wiring:

• Unplug the main unit, the one with the antennas
• connect Gimbal CAN bus (High, Low) wires to the CAN tranciever. No need to add ground
• power microcontroller and tranciever with 5V

Thats it.

PS. I also removed the termination resistor, not sure if needed, but I was also capturing the signal on the other microcontroller running micropython.

[krvcz]

For wiring:

• Unplug the main unit, the one with the antennas
• connect Gimbal CAN bus (High, Low) wires to the CAN tranciever. No need to add ground
• power microcontroller and tranciever with 5V

Thats it.

PS. I also removed the termination resistor, not sure if needed, but I was also capturing the signal on the other microcontroller running micropython.

Thanks a lot ! Soon as possible i will inform you about progress or possible errors . Is there a version with 2 Can buses in the picture?

[JohnieBraaf]

Edit: yes, not sure why, but only 1 is actually communicating. Its the purple and grey wires. I think it is the 2 on the right.
Btw, to solve your error, you probably need to download or enable the middleware LWIP in STM-Cube IDE.

[krvcz]

Edit: yes, not sure why, but only 1 is actually communicating. Its the purple and grey wires. I think it is the 2 on the right.
Btw, to solve your error, you probably need to download or enable the middleware LWIP in STM-Cube IDE.

Ok, so before I have connected board with 2 CAN's, so now should i download older program with 2 CAN in code, right ?
if it will not working with 2 CAN i'm going to try with only one CAN

[JohnieBraaf]

You can have a look at my micropython implementation. It's probably much easier to understand. It's working but not finished.

Micropython-S1.zip

[JohnieBraaf]

"Ok, so before I have connected board with 2 CAN's, so now should i download older program with 2 CAN in code, right ?
if it will not working with 2 CAN i'm going to try with only one CAN"

That version of the code has far less features. And it's actually great to not have to power the main unit. saves battery, so I would say better to have only 1 can.

Also in Micropython I first had a passthrough desing but I was running into performance limitations.

[krvcz]

Unfortunately, at the moment I am limited to STM32. I will keep you posted on the progress.
Does your version of micropython use a Rasberry microcontroller?
I would like to have an alternative solution in case of stm problem.