Upstreamed to 3.18.103

Documentation/devicetree/bindings/arm/davinci.txt

@@ -9,6 +9,10 @@ EnBW AM1808 based CMC board
 Required root node properties:
     - compatible = "enbw,cmc", "ti,da850;
 
+LEGO MINDSTORMS EV3 (AM1808 based)
+Required root node properties:
+    - compatible = "lego,ev3", "ti,da850";
+
 Generic DaVinci Boards
 ----------------------
 

Documentation/devicetree/bindings/display/bridge/ti,ths8135.txt

@@ -0,0 +1,46 @@
+THS8135 Video DAC
+-----------------
+
+This is the binding for Texas Instruments THS8135 Video DAC bridge.
+
+Required properties:
+
+- compatible: Must be "ti,ths8135"
+
+Required nodes:
+
+This device has two video ports. Their connections are modelled using the OF
+graph bindings specified in Documentation/devicetree/bindings/graph.txt.
+
+- Video port 0 for RGB input
+- Video port 1 for VGA output
+
+Example
+-------
+
+vga-bridge {
+	compatible = "ti,ths8135";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			vga_bridge_in: endpoint {
+				remote-endpoint = <&lcdc_out_vga>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			vga_bridge_out: endpoint {
+				remote-endpoint = <&vga_con_in>;
+			};
+		};
+	};
+};

Documentation/devicetree/bindings/dma/snps-dma.txt

@@ -58,6 +58,6 @@ Example:
 		interrupts = <0 35 0x4>;
 		status = "disabled";
 		dmas = <&dmahost 12 0 1>,
-			<&dmahost 13 0 1 0>;
+			<&dmahost 13 1 0>;
 		dma-names = "rx", "rx";
 	};

Documentation/devicetree/bindings/net/can/k61-can.txt

@@ -3,7 +3,7 @@
 This driver implements SPI slave protocol for Freescale K61 CAN controller.
 
 Required properties:
-  - compatible: Should be "fsl,k61" or "nxp,mpc5746c".
+  - compatible: Should be "fsl,k61".
   - reg: Should contain SPI chip select.
   - interrupt-parent: Should specify interrupt controller for the interrupt.
   - interrupts: Should contain IRQ line for the CAN controller.

Documentation/devicetree/bindings/net/can/qti-can.txt

@@ -0,0 +1,48 @@
+* QTI CAN driver *
+
+Required properties:
+  - compatible: Should be "qcom,renesas,rh850" or "qcom,nxp,mpc5746c".
+  - reg: Should contain SPI chip select.
+  - interrupt-parent: Should specify interrupt controller for the interrupt.
+  - interrupts: Should contain IRQ line for the CAN controller.
+  - spi-max-frequency: Should contain maximum spi clock frequency for slave device
+  - qcom,clk-freq-mhz : The frequency at which the CAN clock should be configured.
+  - qcom,max-can-channels : Maximum number of CAN channels supported by the controller.
+
+Optional properties:
+  - qcom,reset-gpio: Reference to the GPIO connected to the reset input.
+  - pinctrl-names : Names corresponding to the numbered pinctrl states.
+  - pinctrl-0 : This explains the active state of the GPIO line.
+  - pinctrl-1 : This explains the suspend state of the GPIO line.
+  - qcom,bits-per-word: Indicate how many bits are in a SPI frame. e.g.: 8, 16, 32.
+                   Default to 16.
+  - qcom,reset-delay-msec: Delay in milliseconds to be applied after resetting the chip.
+    This is applicable only if the reset-gpio is specified. Default value is 1 ms.
+  - qcom,support-can-fd: Whether CAN FD mode is supported or not.
+  - qcom,can-fw-cmd-timeout-req: Whether a timeout is required if we don't get a response from
+    the firmware after flash write.
+  - qcom,can-fw-cmd-timeout-ms: The duration after which timeout will happen if we don't get a
+    response from the firmware.
+  - qcom,rem-all-buffering-timeout-ms: The duration after which timeout will happen if we don't get a
+    response from the firmware while trying to remove all the buffered frames IDs from flash.
+
+Example:
+
+can-controller@0 {
+	compatible = "qcom,nxp,mpc5746c";
+	reg = <0>;
+	spi-max-frequency = <9600000>;
+	interrupt-parent = <&tlmm_pinmux>;
+	interrupts = <87 0>;
+	qcom,reset-gpio = <&tlmm_pinmux 89 0x1>;
+	qcom,clk-freq-mhz = <20000000>;
+	qcom,max-can-channels = <2>;
+	qcom,bits-per-word = <8>;
+	qcom,reset-delay-msec = <150>;
+	qcom,can-fw-cmd-timeout-req;
+	qcom,can-fw-cmd-timeout-ms = <400>;
+	qcom,rem-all-buffering-timeout-ms = <2000>;
+	pinctrl-names = "active", "sleep";
+	pinctrl-0 = <&can_rst_on>;
+	pinctrl-1 = <&can_rst_off>;
+};

Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt

@@ -35,6 +35,15 @@ Optional properties:
 - ti,palmas-enable-dvfs2: Enable DVFS2. Configure pins for DVFS2 mode.
 	Selection primary or secondary function associated to GPADC_START
 	and SYSEN2 pin/pad for DVFS2 interface
+- ti,palmas-override-powerhold: This is applicable for PMICs for which
+	GPIO7 is configured in POWERHOLD mode which has higher priority
+	over DEV_ON bit and keeps the PMIC supplies on even after the DEV_ON
+	bit is turned off. This property enables driver to over ride the
+	POWERHOLD value to GPIO7 so as to turn off the PMIC in power off
+	scenarios. So for GPIO7 if ti,palmas-override-powerhold is set
+	then the GPIO_7 field should never be muxed to anything else.
+	It should be set to POWERHOLD by default and only in case of
+	power off scenarios the driver will over ride the mux value.
 
 This binding uses the following generic properties as defined in
 pinctrl-bindings.txt:

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -92,6 +92,7 @@ karo	Ka-Ro electronics GmbH
 keymile	Keymile GmbH
 lacie	LaCie
 lantiq	Lantiq Semiconductor
+lego	LEGO Systems A/S
 lenovo	Lenovo Group Ltd.
 invn	InvenSense Inc.
 isl	Intersil

Documentation/filesystems/ext4.txt

@@ -233,7 +233,7 @@ data_err=ignore(*)	Just print an error message if an error occurs
 data_err=abort		Abort the journal if an error occurs in a file
 			data buffer in ordered mode.
 
-grpid			Give objects the same group ID as their creator.
+grpid			New objects have the group ID of their parent.
 bsdgroups
 
 nogrpid		(*)	New objects have the group ID of their creator.

Documentation/filesystems/proc.txt

@@ -335,7 +335,7 @@ address           perms offset  dev   inode      pathname
 a7cb1000-a7cb2000 ---p 00000000 00:00 0
 a7cb2000-a7eb2000 rw-p 00000000 00:00 0
 a7eb2000-a7eb3000 ---p 00000000 00:00 0
-a7eb3000-a7ed5000 rw-p 00000000 00:00 0          [stack:1001]
+a7eb3000-a7ed5000 rw-p 00000000 00:00 0
 a7ed5000-a8008000 r-xp 00000000 03:00 4222       /lib/libc.so.6
 a8008000-a800a000 r--p 00133000 03:00 4222       /lib/libc.so.6
 a800a000-a800b000 rw-p 00135000 03:00 4222       /lib/libc.so.6
@@ -367,42 +367,13 @@ is not associated with a file:
 
  [heap]                   = the heap of the program
  [stack]                  = the stack of the main process
- [stack:1001]             = the stack of the thread with tid 1001
  [vdso]                   = the "virtual dynamic shared object",
                             the kernel system call handler
  [anon:<name>]            = an anonymous mapping that has been
                             named by userspace
 
  or if empty, the mapping is anonymous.
 
-The /proc/PID/task/TID/maps is a view of the virtual memory from the viewpoint
-of the individual tasks of a process. In this file you will see a mapping marked
-as [stack] if that task sees it as a stack. This is a key difference from the
-content of /proc/PID/maps, where you will see all mappings that are being used
-as stack by all of those tasks. Hence, for the example above, the task-level
-map, i.e. /proc/PID/task/TID/maps for thread 1001 will look like this:
-
-08048000-08049000 r-xp 00000000 03:00 8312       /opt/test
-08049000-0804a000 rw-p 00001000 03:00 8312       /opt/test
-0804a000-0806b000 rw-p 00000000 00:00 0          [heap]
-a7cb1000-a7cb2000 ---p 00000000 00:00 0
-a7cb2000-a7eb2000 rw-p 00000000 00:00 0
-a7eb2000-a7eb3000 ---p 00000000 00:00 0
-a7eb3000-a7ed5000 rw-p 00000000 00:00 0          [stack]
-a7ed5000-a8008000 r-xp 00000000 03:00 4222       /lib/libc.so.6
-a8008000-a800a000 r--p 00133000 03:00 4222       /lib/libc.so.6
-a800a000-a800b000 rw-p 00135000 03:00 4222       /lib/libc.so.6
-a800b000-a800e000 rw-p 00000000 00:00 0
-a800e000-a8022000 r-xp 00000000 03:00 14462      /lib/libpthread.so.0
-a8022000-a8023000 r--p 00013000 03:00 14462      /lib/libpthread.so.0
-a8023000-a8024000 rw-p 00014000 03:00 14462      /lib/libpthread.so.0
-a8024000-a8027000 rw-p 00000000 00:00 0
-a8027000-a8043000 r-xp 00000000 03:00 8317       /lib/ld-linux.so.2
-a8043000-a8044000 r--p 0001b000 03:00 8317       /lib/ld-linux.so.2
-a8044000-a8045000 rw-p 0001c000 03:00 8317       /lib/ld-linux.so.2
-aff35000-aff4a000 rw-p 00000000 00:00 0
-ffffe000-fffff000 r-xp 00000000 00:00 0          [vdso]
-
 The /proc/PID/smaps is an extension based on maps, showing the memory
 consumption for each of the process's mappings. For each of mappings there
 is a series of lines such as the following:

Makefile

@@ -1,6 +1,6 @@
 VERSION = 3
 PATCHLEVEL = 18
-SUBLEVEL = 71
+SUBLEVEL = 103
 EXTRAVERSION =
 NAME = Diseased Newt
 
@@ -775,6 +775,9 @@ KBUILD_CFLAGS += $(call cc-disable-warning, pointer-sign)
 # disable invalid "can't wrap" optimizations for signed / pointers
 KBUILD_CFLAGS	+= $(call cc-option,-fno-strict-overflow)
 
+# Make sure -fstack-check isn't enabled (like gentoo apparently did)
+KBUILD_CFLAGS  += $(call cc-option,-fno-stack-check,)
+
 # conserve stack if available
 KBUILD_CFLAGS   += $(call cc-option,-fconserve-stack)
 

arch/alpha/kernel/console.c

@@ -20,6 +20,7 @@
 struct pci_controller *pci_vga_hose;
 static struct resource alpha_vga = {
 	.name	= "alpha-vga+",
+	.flags	= IORESOURCE_IO,
 	.start	= 0x3C0,
 	.end	= 0x3DF
 };

arch/alpha/kernel/pci_impl.h

@@ -143,7 +143,8 @@ struct pci_iommu_arena
 };
 
 #if defined(CONFIG_ALPHA_SRM) && \
-    (defined(CONFIG_ALPHA_CIA) || defined(CONFIG_ALPHA_LCA))
+    (defined(CONFIG_ALPHA_CIA) || defined(CONFIG_ALPHA_LCA) || \
+     defined(CONFIG_ALPHA_AVANTI))
 # define NEED_SRM_SAVE_RESTORE
 #else
 # undef NEED_SRM_SAVE_RESTORE

arch/alpha/kernel/process.c

@@ -274,12 +274,13 @@ copy_thread(unsigned long clone_flags, unsigned long usp,
 	   application calling fork.  */
 	if (clone_flags & CLONE_SETTLS)
 		childti->pcb.unique = regs->r20;
+	else
+		regs->r20 = 0;	/* OSF/1 has some strange fork() semantics.  */
 	childti->pcb.usp = usp ?: rdusp();
 	*childregs = *regs;
 	childregs->r0 = 0;
 	childregs->r19 = 0;
 	childregs->r20 = 1;	/* OSF/1 has some strange fork() semantics.  */
-	regs->r20 = 0;
 	stack = ((struct switch_stack *) regs) - 1;
 	*childstack = *stack;
 	childstack->r26 = (unsigned long) ret_from_fork;

arch/arc/kernel/entry.S

@@ -315,6 +315,12 @@ ENTRY(EV_MachineCheck)
 	lr  r0, [efa]
 	mov r1, sp
 
+	; hardware auto-disables MMU, re-enable it to allow kernel vaddr
+	; access for say stack unwinding of modules for crash dumps
+	lr	r3, [ARC_REG_PID]
+	or	r3, r3, MMU_ENABLE
+	sr	r3, [ARC_REG_PID]
+
 	lsr  	r3, r2, 8
 	bmsk 	r3, r3, 7
 	brne    r3, ECR_C_MCHK_DUP_TLB, 1f

arch/arc/mm/tlb.c

@@ -689,9 +689,6 @@ void do_tlb_overlap_fault(unsigned long cause, unsigned long address,
 
 	local_irq_save(flags);
 
-	/* re-enable the MMU */
-	write_aux_reg(ARC_REG_PID, MMU_ENABLE | read_aux_reg(ARC_REG_PID));
-
 	/* loop thru all sets of TLB */
 	for (set = 0; set < mmu->sets; set++) {
 

arch/arm/Kconfig-nommu

@@ -34,8 +34,7 @@ config PROCESSOR_ID
 	  used instead of the auto-probing which utilizes the register.
 
 config REMAP_VECTORS_TO_RAM
-	bool 'Install vectors to the beginning of RAM' if DRAM_BASE
-	depends on DRAM_BASE
+	bool 'Install vectors to the beginning of RAM'
 	help
 	  The kernel needs to change the hardware exception vectors.
 	  In nommu mode, the hardware exception vectors are normally

arch/arm/boot/dts/am335x-evmsk.dts

@@ -646,6 +646,7 @@
 	ti,non-removable;
 	bus-width = <4>;
 	cap-power-off-card;
+	keep-power-in-suspend;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins>;
 

arch/arm/boot/dts/am4372.dtsi

@@ -702,7 +702,8 @@
 			reg = <0x48038000 0x2000>,
 			      <0x46000000 0x400000>;
 			reg-names = "mpu", "dat";
-			interrupts = <80>, <81>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "tx", "rx";
 			status = "disabled";
 			dmas = <&edma 8>,
@@ -716,7 +717,8 @@
 			reg = <0x4803C000 0x2000>,
 			      <0x46400000 0x400000>;
 			reg-names = "mpu", "dat";
-			interrupts = <82>, <83>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "tx", "rx";
 			status = "disabled";
 			dmas = <&edma 10>,

arch/arm/boot/dts/dra7-evm.dts

@@ -182,6 +182,8 @@
 	tps659038: tps659038@58 {
 		compatible = "ti,tps659038";
 		reg = <0x58>;
+		ti,palmas-override-powerhold;
+		ti,system-power-controller;
 
 		tps659038_pmic {
 			compatible = "ti,tps659038-pmic";

arch/arm/boot/dts/dra7.dtsi

@@ -118,6 +118,7 @@
 				device_type = "pci";
 				ranges = <0x81000000 0 0          0x03000 0 0x00010000
 					  0x82000000 0 0x20013000 0x13000 0 0xffed000>;
+				bus-range = <0x00 0xff>;
 				#interrupt-cells = <1>;
 				num-lanes = <1>;
 				ti,hwmods = "pcie1";
@@ -153,6 +154,7 @@
 				device_type = "pci";
 				ranges = <0x81000000 0 0          0x03000 0 0x00010000
 					  0x82000000 0 0x30013000 0x13000 0 0xffed000>;
+				bus-range = <0x00 0xff>;
 				#interrupt-cells = <1>;
 				num-lanes = <1>;
 				ti,hwmods = "pcie2";

arch/arm/boot/dts/kirkwood-openblocks_a7.dts

@@ -53,7 +53,8 @@
 		};
 
 		pinctrl: pin-controller@10000 {
-			pinctrl-0 = <&pmx_dip_switches &pmx_gpio_header>;
+			pinctrl-0 = <&pmx_dip_switches &pmx_gpio_header
+				     &pmx_gpio_header_gpo>;
 			pinctrl-names = "default";
 
 			pmx_uart0: pmx-uart0 {
@@ -85,11 +86,16 @@
 			 * ground.
 			 */
 			pmx_gpio_header: pmx-gpio-header {
-				marvell,pins = "mpp17", "mpp7", "mpp29", "mpp28",
+				marvell,pins = "mpp17", "mpp29", "mpp28",
 					       "mpp35", "mpp34", "mpp40";
 				marvell,function = "gpio";
 			};
 
+			pmx_gpio_header_gpo: pxm-gpio-header-gpo {
+				marvell,pins = "mpp7";
+				marvell,function = "gpo";
+			};
+
 			pmx_gpio_init: pmx-init {
 				marvell,pins = "mpp38";
 				marvell,function = "gpio";