Lineage 15.0

Documentation/devicetree/bindings/fb/mdss-dsi-panel.txt

@@ -61,6 +61,30 @@ Required properties:
 						 transmitted
 					byte 5, 6: 16 bits length in network byte order
 					byte 7 and beyond: number byte of payload
+- qcom,mdss-dsi-lp-mode-on:		This is used to enable display low persistence mode.
+					A byte stream formed by multiple dcs packets base on
+					qcom dsi controller protocol.
+					byte 0: dcs data type
+					byte 1: set to indicate this is an individual packet
+						 (no chain)
+					byte 2: virtual channel number
+					byte 3: expect ack from client (dcs read command)
+					byte 4: wait number of specified ms after dcs command
+						 transmitted
+					byte 5, 6: 16 bits length in network byte order
+					byte 7 and beyond: number byte of payload
+- qcom,mdss-dsi-lp-mode-off:		This is used to disable display low persistence mode.
+					A byte stream formed by multiple dcs packets base on
+					qcom dsi controller protocol.
+					byte 0: dcs data type
+					byte 1: set to indicate this is an individual packet
+						 (no chain)
+					byte 2: virtual channel number
+					byte 3: expect ack from client (dcs read command)
+					byte 4: wait number of specified ms after dcs command
+						 transmitted
+					byte 5, 6: 16 bits length in network byte order
+					byte 7 and beyond: number byte of payload
 - qcom,mdss-dsi-post-panel-on-command:	same as "qcom,mdss-dsi-on-command" except commands are
 					sent after displaying an image.
 
@@ -611,6 +635,9 @@ Example:
 		qcom,mdss-dsi-on-command-state = "dsi_lp_mode";
 		qcom,mdss-dsi-off-command = [22 01 00 00 00 00 00];
 		qcom,mdss-dsi-off-command-state = "dsi_hs_mode";
+		qcom,mdss-dsi-lp-mode-on = [32 01 00 00 00 00 02 00 00
+					29 01 00 00 10 00 02 FF 99];
+		qcom,mdss-dsi-lp-mode-off = [22 01 00 00 00 00 00];
 		qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled";
 		qcom,mdss-dsi-pan-enable-dynamic-fps;
 		qcom,mdss-dsi-pan-fps-update = "dfps_suspend_resume_mode";

Documentation/devicetree/bindings/media/video/msm-vfe.txt

@@ -23,7 +23,6 @@ Required properties for child node:
     Only needed for child node.
     - "vfe" - Required.
     - "vfe_vbif" - Optional for "vfe32". Required for "vfe40".
-    - "vfe_fuse" - Optional.
 - interrupts : should contain the vfe interrupt.
 - interrupt-names : should specify relevant names to each interrupts
   property defined.
@@ -53,10 +52,9 @@ Example:
 vfe0: qcom,vfe0@fda10000 {
 	cell-index = <0>;
 	compatible = "qcom,vfe44";
-	reg = <0xfda10000 0x1000>,
-		<0xfda40000 0x200>,
-		<0xa4174 0x8>;
-	reg-names = "vfe", "vfe_vbif", "vfe_fuse";
+	reg = <0xfda10000 0x1000>;
+		<0xfda40000 0x200>;
+	reg-names = "vfe", "vfe_vbif";
 	interrupts = <0 57 0>;
 	interrupt-names = "vfe";
 	vdd-supply = <&gdsc_vfe>;
@@ -107,10 +105,9 @@ vfe0: qcom,vfe0@fda10000 {
 vfe1: qcom,vfe1@fda14000 {
 	cell-index = <1>;
 	compatible = "qcom,vfe44";
-	reg = <0xfda14000 0x1000>,
-		<0xfda40000 0x200>,
-		<0xa4174 0x8>;
-	reg-names = "vfe", "vfe_vbif", "vfe_fuse";
+	reg = <0xfda14000 0x1000>;
+		<0xfda40000 0x200>;
+	reg-names = "vfe", "vfe_vbif";
 	interrupts = <0 58 0>;
 	interrupt-names = "vfe";
 	vdd-supply = <&gdsc_vfe>;

arch/arm/boot/dts/qcom/Makefile

@@ -251,6 +251,9 @@ dtb-$(CONFIG_ARCH_MSM8940) += msm8940-pmi8937-cdp.dtb \
 	msm8940-pmi8940-rcm.dtb \
 	msm8940-pmi8940-qrd-sku7.dtb
 
+ifeq ($(CONFIG_MACH_XIAOMI_MSM8953),y)
+dtb-$(CONFIG_MACH_XIAOMI_MIDO) += msm8953-qrd-sku3.dtb
+else
 dtb-$(CONFIG_ARCH_MSM8953) += msm8953-sim.dtb \
 	msm8953-rumi.dtb \
 	msm8953-cdp.dtb \
@@ -282,6 +285,7 @@ dtb-$(CONFIG_ARCH_SDM450) += sdm450-rcm.dtb \
 	sdm450-qrd.dtb \
 	sdm450-pmi8940-mtp.dtb \
 	sdm450-pmi8937-mtp.dtb
+endif
 
 dtb-$(CONFIG_ARCH_MDM9607) += mdm9607-rumi.dtb \
 	mdm9607-cdp.dtb \

arch/arm/boot/dts/qcom/apq8017-io-expander-cdp.dtsi

@@ -0,0 +1,95 @@
+/*
+ * Copyright (c) 2015-2017, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include "msm8917-pinctrl.dtsi"
+#include "msm8917-camera-sensor-cdp.dtsi"
+
+&soc {
+	usbhub_vbus_vreg: usbhub_vbus_vreg {
+		compatible = "regulator-fixed";
+		regulator-name = "usbhub_vbus_vreg";
+		gpio = <&ioexp_gpios 3 0>;
+		enable-active-high;
+	};
+
+	usbeth_vbus_vreg: usbeth_vbus_vreg {
+		compatible = "regulator-fixed";
+		regulator-name = "usbeth_vbus_vreg";
+		gpio = <&ioexp_gpios 7 0>;
+		enable-active-high;
+		vin-supply = <&usbhub_vbus_vreg>;
+	};
+};
+
+/* SX1509q i/o expander */
+&i2c_2 {
+	status = "ok";
+	ioexp2_gpios: sx150x@3e {
+		status = "ok";
+		compatible = "sx1509q";
+		#gpio-cells = <2>;
+		gpio-controller;
+		reg = <0x3E>; /* I2C Client Addr */
+		sx150x,pullup_ena = <0x0>;
+		sx150x,pulldn_ena = <0x0>;
+		sx150x,float_ena = <0x00>;
+		sx150x,polarity = <0x0>;
+		sx150x,gpio_base= <300>;
+	};
+};
+
+/* SX1508q i/o expander */
+&i2c_4 {
+	status = "ok";
+	ioexp_gpios: sx150x@20 {
+		status = "ok";
+		compatible = "sx1508q";
+		#gpio-cells = <2>;
+		gpio-controller;
+		reg = <0x20>; /* I2C Client Addr */
+		sx150x,pullup_ena = <0x0>;
+		sx150x,pulldn_ena = <0x0>;
+		sx150x,float_ena = <0x00>;
+		sx150x,polarity = <0x0>;
+		sx150x,gpio_base = <200>;
+		vdd-supply = <&pm8917_l6>;
+		qcom,vdd-max-voltage = <1800000>;
+		qcom,vdd-min-voltage = <1800000>;
+	};
+	/* usb2533 flex hub */
+	usb2533@2c {
+		status = "disabled";
+		compatible = "qcom,usb2533-flex-hub";
+		reg = <0x2d>;
+		vbus-supply = <&usbeth_vbus_vreg>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb2533_hub_reset>;
+		qcom,hub-reset-gpio = <&tlmm 100 0>;
+		qcom,usbeth-reset-gpio = <&ioexp_gpios 5 0>;
+	};
+};
+
+/* KS8851 eth over spi */
+&spi_6 {
+	status = "ok";
+	ethernet@0 {
+		status = "ok";
+		compatible = "micrel,ks8851";
+		reg = <1>;  /* CS-1 */
+		interrupt-parent = <&tlmm>;
+		interrupts = <97 0>;
+		reset-gpios = <&ioexp_gpios 2 0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+

arch/arm/boot/dts/qcom/apq8017-no-pmi-wcd-rome-cdp.dts

@@ -17,6 +17,7 @@
 #include "apq8017-no-pmi-cdp.dtsi"
 #include "apq8017-rome.dtsi"
 #include "apq8017-audio.dtsi"
+#include "apq8017-io-expander-cdp.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. APQ8017 CDP no-PMI \

arch/arm/boot/dts/qcom/batterydata-qrd-coslight-4v4-4100mah.dtsi

@@ -0,0 +1,48 @@
+
+qcom,2786095_mido_coslight_4100mah_averaged_masterslave_feb3rd2017 {
+	qcom,max-voltage-uv = <4400000>;
+	qcom,nom-batt-capacity-mah = <4100>;
+	qcom,batt-id-kohm = <50>;
+	qcom,battery-beta = <3435>;
+	qcom,battery-type = "qrd_msm8953_coslight_4100mah";
+	qcom,chg-rslow-comp-c1 = <3439671>;
+	qcom,chg-rslow-comp-c2 = <5394943>;
+	qcom,chg-rs-to-rslow = <823652>;
+	qcom,chg-rslow-comp-thr = <0xAE>;
+	qcom,checksum = <0xF02E>;
+	qcom,gui-version = "PMI8950GUI - 2.0.0.16";
+	qcom,fg-profile-data = [
+		 DF 83 B4 7C
+		 E0 80 A2 76
+		 56 83 B7 5E
+		 DF 82 41 8E
+		 40 82 BC 98
+		 C2 B6 78 C2
+		 57 17 EA 83
+		 B7 7C CA 80
+		 59 76 4F 83
+		 37 6B 71 78
+		 EE 86 41 82
+		 FA 99 50 BD
+		 65 CA 55 0D
+		 07 10 F0 58
+		 14 70 DA FC
+		 05 3E F6 35
+		 FE 12 00 00
+		 3B 3D 7B 30
+		 92 45 00 00
+		 00 00 00 00
+		 00 00 00 00
+		 7B 6A 86 69
+		 1C 68 1C 7B
+		 0C 6C 60 60
+		 63 6A F6 7A
+		 BF 64 C1 58
+		 C0 84 BB 7E
+		 1B C9 61 20
+		 5F A0 71 0C
+		 28 00 FF 36
+		 F0 11 30 03
+		 00 00 00 0C
+	];
+};

arch/arm/boot/dts/qcom/batterydata-qrd-desay-4v4-4100mah.dtsi

@@ -0,0 +1,62 @@
+/* Copyright (c) 2015-2016, The Linux Foundation. All rights reserved.
+ * Copyright (C) 2017 XiaoMi, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+qcom,2508175_bn41hdesay_4100mah_averaged_masterslave_jun27th2016 {
+	qcom,max-voltage-uv = <4400000>;
+	qcom,nom-batt-capacity-mah = <4100>;
+	qcom,batt-id-kohm = <82>;
+	qcom,battery-beta = <3435>;
+	qcom,battery-type = "qrd_msm8953_desay_4100mah";
+	qcom,fastchg-current-ma = <2000>;
+	qcom,fg-cc-cv-threshold-mv = <4390>;
+	qcom,chg-rslow-comp-c1 = <2760396>;
+	qcom,chg-rslow-comp-c2 = <3348384>;
+	qcom,chg-rs-to-rslow = <870409>;
+	qcom,chg-rslow-comp-thr = <0x99>;
+	qcom,checksum = <0xFA46>;
+	qcom,gui-version = "PMI8950GUI - 2.0.0.16";
+	qcom,fg-profile-data = [
+		 DE 83 BE 7C
+		 15 81 58 77
+		 62 83 13 74
+		 3F 89 50 94
+		 1D 82 DE 99
+		 AC BC 0C C9
+		 56 10 10 88
+		 A4 7E 60 82
+		 D2 7C 48 83
+		 30 72 2E 75
+		 75 6D 4E 82
+		 80 99 A9 BC
+		 5C C9 5E 0C
+		 C9 0F 82 5A
+		 14 70 DA FC
+		 20 2F 05 46
+		 07 41 00 00
+		 FF 4C 56 3B
+		 AF 41 00 00
+		 00 00 00 00
+		 00 00 00 00
+		 4D 70 1A 6A
+		 C9 74 9E 89
+		 9F 77 D2 70
+		 A3 58 9F 81
+		 91 74 A5 68
+		 7D 66 B5 9B
+		 2F 05 63 F3
+		 64 A0 71 0C
+		 28 00 FF 36
+		 F0 11 30 03
+		 00 00 00 0C
+	];
+};

arch/arm/boot/dts/qcom/batterydata-qrd-desay-lisheng-4v4-4100mah.dtsi

@@ -0,0 +1,48 @@
+
+qcom,2781148_mido_desay_4100mah_averaged_masterslave_feb3rd2017 {
+	qcom,max-voltage-uv = <4400000>;
+	qcom,nom-batt-capacity-mah = <4100>;
+	qcom,batt-id-kohm = <62>;
+	qcom,battery-beta = <3435>;
+	qcom,battery-type = "batterydata-qrd-desay-lisheng-4v4-4100mah";
+	qcom,chg-rslow-comp-c1 = <2747468>;
+	qcom,chg-rslow-comp-c2 = <3764702>;
+	qcom,chg-rs-to-rslow = <770184>;
+	qcom,chg-rslow-comp-thr = <0xA2>;
+	qcom,checksum = <0x3826>;
+	qcom,gui-version = "PMI8950GUI - 2.0.0.16";
+	qcom,fg-profile-data = [
+		 F0 83 6D 7D
+		 90 81 15 7C
+		 5C 83 50 67
+		 0E 83 A6 8D
+		 22 82 AE 9A
+		 28 BE B5 CB
+		 5A 0E FC 83
+		 78 7D 8C 81
+		 0B 7C 62 83
+		 D4 65 5D 88
+		 2D 94 57 82
+		 BB 99 28 BD
+		 42 CA 52 0D
+		 2A 10 98 59
+		 14 70 DA FC
+		 09 44 6E 3D
+		 AF 39 00 00
+		 23 47 66 38
+		 AF 31 00 00
+		 00 00 00 00
+		 00 00 00 00
+		 28 6B 33 6A
+		 E6 70 BF 88
+		 0C 74 27 69
+		 7B 5A 38 80
+		 26 6E 19 68
+		 25 6E 46 A1
+		 1D D3 5A 1B
+		 5C A0 71 0C
+		 28 00 FF 36
+		 F0 11 30 03
+		 00 00 00 0C
+	];
+};