SwiftProForArduino/lib/Marlin/pins_Swift.h at 553a66ca9c6bae0d0aa85419f4780040bd31d5e7 · uArm-Developer/SwiftProForArduino · GitHub

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */


#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
  #error "Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
#endif

#ifndef BOARD_NAME
  #define BOARD_NAME "Swift 1.0"
#endif

#define LARGE_FLASH true


#define SERVO0_PIN       6

//#define SERVO1_PIN          6
//#define SERVO2_PIN          5
//#define SERVO3_PIN          4

#define X_MIN_PIN           27
#ifndef X_MAX_PIN
  //#define X_MAX_PIN         41
#endif
#define Y_MIN_PIN          42
//#define Y_MAX_PIN          25
#define Z_MIN_PIN          29
//#define Z_MAX_PIN          29
#ifndef Z_MIN_PROBE_PIN
  //#define Z_MIN_PROBE_PIN  32
#endif

#define X_STEP_PIN         54	//S
#define X_DIR_PIN          55	//S
#define X_ENABLE_PIN       38	//S

#define Y_STEP_PIN         60	//S
#define Y_DIR_PIN          61	//S
#define Y_ENABLE_PIN       56	//S

#define Z_STEP_PIN         46	//S
#define Z_DIR_PIN          48	//S
#define Z_ENABLE_PIN       62	//S

#define E0_STEP_PIN        26	//S
#define E0_DIR_PIN         28	//S
#define E0_ENABLE_PIN      24	//S

#define E1_STEP_PIN        36
#define E1_DIR_PIN         34
#define E1_ENABLE_PIN      30

#define SDSS               53	// sd card cs pin
#define LED_PIN            2	// R 13

#define LED_G			 	3	//G
#define LED_B				5   //B

#define BEEPER_PIN 44

#define KEY_MENU_PIN			//PE6
#define KEY_PLAY_PIN			// PE7
#define KEY_STATE_PIN		11

#define E2PROM_SCL						// 12 PB7
#define E2PROM_SDA						// 13 PB6

#define X_SCL						// PD6
#define X_SDA						// PD5

#define Y_SCL			34			// PC3
#define Y_SDA			36			// PC1

#define Z_SCL						// PH7
#define Z_SDA						// PH2

#define SERVO_HAND_ROT_ANALOG_PIN   A3

#define   POWER_DETECT  A5

// Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
#define FILWIDTH_PIN        -1 // 47	//5 // ANALOG NUMBERING

// define digital pin 4 for the filament runout sensor. Use the RAMPS 1.4 digital input 4 on the servos connector
#define FIL_RUNOUT_PIN      49	// 4

//#define PS_ON_PIN          12	// PS POWER
#define TEMP_0_PIN         13   // ANALOG NUMBERING
#define TEMP_1_PIN         -1	// 14   // ANALOG NUMBERING
#define TEMP_BED_PIN       15 	//15   // ANALOG NUMBERING

#define HEATER_0_PIN     9


#define FAN_PIN        	8
#define HEATER_BED_PIN 	39

#define VALVE_EN		4
//#define PUMP_EN	//PG4


#define PUMP_FEEDBACK	A9

//#define GRIPPER		 pC7
#define GRIPPER_FEEDBACK	22
//#define HW_PIN_0


#if ENABLED(Z_PROBE_SLED)
  #define SLED_PIN           -1
#endif


  #define MOSFET_D_PIN  -1


#ifndef FAN_PIN
  #define FAN_PIN 4      // IO pin. Buffer needed
#endif